ndpd.conf(4)

Skip to ContentSun and Oracle Channel Sun How to Buy Log In

man pages section 4: File Formats

Contidos dentro

Localizar Mais Documentação

Destaques de Recursos de Suporte

Fazer download desta apostila em PDF (3087 KB)

Name

ndpd.conf– configuration file for IPv6 router autoconfiguration

Synopsis

/etc/inet/ndpd.conf

Description

The ndpd.conf file contains configuration information for in.ndpd(1M). On a host, this file does not need to exist or can be empty. The file has one configuration entry per line; note that lines can be extended with a backslash (\) followed by a NEWLINE. There are four forms of configuration entries which are identified by the first field on the line: ifdefault, prefixdefault, if, or prefix. The ifdefault and if entries set interface configuration variables. The former establishes the routing behavior for all interfaces, the latter sets per-interface parameters. Any ifdefault entries must precede any if entries in the file.

The prefixdefault and prefix entries control prefix configuration variables. prefixdefault establishes the default behavior for all prefix advertisements on all interfaces. The prefix keyword advertises per-prefix information. Any prefixdefault entries must precede any prefix entries in the file.

Each ifdefault entry is composed of a single line of the form:

ifdefault [ if-variable-name value ]*

Each if entry is composed of a single line of the form:

if interface [ if-variable-name value ]*

Each prefixdefault entry is composed of a single line of the form:

prefixdefault [ prefix-variable-name value ]*

Each prefix entry is composed of a single line of the form:

prefix prefix/prefix_length interface [ prefix-variable-name value ]*

Fields are separated by either SPACE or TAB characters. A `#' (number sign) indicates the beginning of a comment. Characters up to the end of the line are not interpreted by routines that search this file.

interface

The name of a network interface, for example, eri0.

prefix

An IPv6 address in standard hexadecimal notation, for example, fec0:0:0:1::0.

prefix_length

A number between 0 and 128.

if-variable-name

An interface variable. Below is the list of interface variables applicable to routers only along with their default values and units as discussed in RFC 2461 and RFC 2462. The Tmp* variables apply to hosts and routers. The Tmp* variables configure temporary address functionality as defined in RFC 3041.

Variable Name           Default    Unit

AdvSendAdvertisements   false      Boolean
DupAddrDetectTransmits  1          Counter
MaxRtrAdvInterval       600        Seconds
MinRtrAdvInterval       200        Seconds
AdvManagedFlag          false      Boolean
AdvOtherConfigFlag      false      Boolean
AdvLinkMTU              0          Bytes
AdvReachableTime        0          Milliseconds
AdvRetransTimer         0          Milliseconds
AdvCurHopLimit          see below  Counter
AdvDefaultLifetime      1800       Seconds

These variables are described as follows:

AdvSendAdvertisements: Indicates whether the node should send out advertisements and respond to router solicitations. You need to explicitly configure this value to turn on router advertisement functions.
DupAddrDetectTransmits: Defines the number of consecutive Neighbor Solicitation messages that the Neighbor Discovery protocol should send during Duplicate Address Detection of the local node's address.
MaxRtrAdvInterval: Specifies the maximum time to wait between sending unsolicited multicast advertisements.
MinRtrAdvInterval: Specifies the minimum amount of time to wait between sending unsolicited multicast advertisements.
AdvManagedFlag: Indicates the value to be placed in the “Manage address configuration” flag in the Router Advertisement. This flag causes hosts to run DHCPv6 to acquire addresses and other configuration information. This flag causes hosts to run DHCPv6 to acquire configuration information, but only if AdvManagedFlag is not set.
AdvOtherConfigFlag: Indicates the value to be placed in the “Other stateful configuration”flag in the Router Advertisement.
AdvLinkMTU: Specifies an MTU value to be sent by the router. The default of zero indicates that the router does not specify MTU options.
AdvReachableTime: Specifies the value in the Reachable Time field in the advertisement messages sent by the router.
AdvRetransTimer: Specifies the value in the Retrans Timer field in the advertisement messages sent by the router.
AdvCurHopLimit: Specifies the value to be placed in the current hop limit field in the advertisement messages sent by the router. The default is the current diameter of the Internet.
AdvDefaultLifetime: Specifies the default lifetime of the router advertisements.

Listed below is the interface variable that applies to both hosts and routers.

Variable Name           Default    Unit

StatefulAddrConf        true       Boolean
StatelessAddrConf       true       Boolean
TmpAddrsEnabled         false      Boolean
TmpValidLifetime        604800     Seconds
                        (1 week)
TmpPreferredLifetime    86400      Seconds
                        (1 day)
TmpRegenAdvance         5          Seconds
TmpMaxDesyncFactor      600        Seconds

StatefulAddrConf: Controls whether the system configures its IPv6 addresses by means of the Stateful Address Autoconfiguration mechanism, also known as DHCPv6, as described in RFC 3315. If enabled (the default), hosts automatically run DHCPv6 based on the “managed” and “other” flags sent by routers. If disabled, in.ndpd will not invoke DHCPv6 automatically. DHCPv6 can still be invoked manually by using ifconfig(1M), in which case in.ndpd automatically sets the prefix length as needed.
StatelessAddrConf: Controls whether the system configures its IPv6 addresses by means of the Stateless Address Autoconfiguration mechanism described in RFC 2462. If enabled hosts (the default) autoconfigure addresses based on prefixes advertised by routers, routers will only autoconfigure addresses based on the prefixes they advertise themselves. In other words, even when enabled, routers do not autoconfigure addresses based on prefixes that other routers advertise. If you specify false for this variable, then the address must be configured manually.
TmpAddrsEnabled: Indicates whether a temporary address should be created for all interfaces or for a particular interface of a node.
TmpValidLifetime: Sets the valid lifetime for a temporary address.
TmpPreferredLifetime: Sets the preferred lifetime of a temporary address.
TmpRegenAdvance: Specifies the lead time in advance of address deprecation for generation of a new temporary address.
TmpMaxDesyncFactor: Sets the upper bound on the DesyncFactor, which is a random value that is used to shorten the preferred lifetime so that clients do not regenerate an address at the same time.

prefix-variable-name

A prefix variable as discussed in RFC 2461 and RFC 2462. The following lists the each interface variable and its default value and unit:

Variable Name	Default	Unit
AdvValidLifetime	2592000	Seconds
AdvOnLinkFlag	true	Boolean
AdvPreferredLifetime	604800	Seconds
AdvAutonomousFlag	true	Boolean
AdvValidExpiration	not set	Date/Time
AdvPreferredExpiration	not set	Date/TIme

These variables are described as follows:

AdvValidLifetime: Specifies the valid lifetime of the prefix that is being configured.
AdvOnLinkFlag: Specifies the value to be placed in the on-link flag (“L-bit”) field in the Prefix Information option.
AdvPreferredLifetime: Specifies the value to be placed in the Preferred Lifetime in the Prefix Information option.
AdvAutonomousFlag: Specifies the value to be placed in the Autonomous Flag field in the Prefix Information option.
AdvValidExpiration: Specifies the valid expiration date of the prefix.
AdvPreferredExpiration: Specifies the preferred expiration date of the prefix.

The AdvValidExpiration and AdvPreferredExpiration variables are used to specify that the lifetime should be decremented in real time as specified in RFC 2461. If an Expiration variable is set, it takes precedence over the corresponding AdvValidLifetime or AdvPreferredLifetime variable setting.

value

The value is a function of the unit. Boolean values are true, false, on, off, 1, or 0.

Values in seconds can have characters appended for day (d), hour h), minute (m) and second (s). The default is seconds. For example, 1h means 1 hour. This is equivalent to the value 3600.

Values in milliseconds can have characters appended for day (d),hour (h), minute (m) second (s), and millisecond (ms). The default is milliseconds. For example, 1h is equivalent to the value 3600000.

Date/time values are strings that use the recommended ISO date format described as “%Y-%m-%d %R”, which represents a 4 digit year, a dash character, a numeric month, a dash character, and a numeric day of the month, followed by one or more whitespace characters and finally a 24 hour clock with hours, a colon, and minutes. For example, 1999-01-31 20:00 means 8pm January 31 in 1999. Since the date/time values contain a space, use single or double quotes to declare the value. For example:

prefixdefault AdvPreferredExpiration '1999-01-31 20:00'

Examples

Example 1 Sending Router Advertisements for all Interfaces

The following example can be used to send router advertisements out to all interfaces:

# Send router advertisements out all interfaces
ifdefault AdvSendAdvertisements on 
prefixdefault AdvOnLinkFlag on AdvAutonomousFlag on

# Advertise a (bogus) global prefix and a site 
# local prefix on three interfaces using the default lifetimes
prefix 2:0:0:9255::0/64      eri0
prefix fec0:0:0:9255::0/64   eri0

prefix 2:0:0:9256::0/64      eri1
prefix fec0:0:0:9256::0/64   eri1

prefix 2:0:0:9259::0/64      eri2
prefix fec0:0:0:9259::0/64   eri2

Attributes

See attributes(5) for descriptions of the following attributes:

ATTRIBUTE TYPE	ATTRIBUTE VALUE
Availability	SUNWcsr
Interface Stability	Committed