Chapter 2 Service Availability Manager Installation and Setup
This chapter discusses the following topics:
Service Availability Manager Software
Service Availability Manager is installed as an add-on
to the SunTM Management Center 3.5 software. The Service Availability Manager
software runs on the following platforms:
-
Solaris™ 2.6, Solaris 7, Solaris 8, and Solaris 9 operating
environments
-
All the platforms on which the Sun Management Center 3.5 agent can run
and that are supported by Sun Management Center 3.5
The Service Availability Manager server layer runs on the Solaris 8 and Solaris
9 operating environments. The LDAP modules are supported only on the Solaris
7, Solaris 8, and Solaris 9 operating environments. For any late-breaking
information, please see the
Sun Management Center 3.5 Release Notes.
The Service Availability Manager add-on software consists of the following packages:
-
SUNWesaes – Service Availability Manager package
for Sun Management Center agent layer
-
SUNWesses – Service Availability Manager package
for Sun Management Center server layer
-
SUNWesces – Service Availability Manager package
for Sun Management Center console layer
-
SUNWeshes – Service Availability Manager online
help package for Sun Management Center server layer
-
SUNWessam – Service Availability Manager package
for the Sun Management Center agent, console, and server layer
-
SUNWfrsam – Service Availability Manager package
for the Sun Management Center agent, console, and server layer for French
Localization
-
SUNWjasam – Service Availability Manager package
for the Sun Management Center agent, console, and server layer for Japanese
Localization
-
SUNWkosam – Service Availability Manager package
for the Sun Management Center agent, console, and server layer for Korean
Localization
-
SUNWcsam – Service Availability Manager package
for the Sun Management Center agent, console, and server layer for Simplified
Chinese Localization
-
SUNWhsam – Service Availability Manager package
for the Sun Management Center agent, console, and server layer for Traditional
Chinese Localization
-
SUNWfrsmh – Service Availability Manager online
help package for Sun Management Center server layer for French Localization
-
SUNWjasmh – Service Availability Manager online
help package for Sun Management Center server layer for Japanese Localization
-
SUNWkosmh – Service Availability Manager online
help package for Sun Management Center server layer for Korean Localization
-
SUNWcsmh – Service Availability Manager online
help package for Sun Management Center server layer for Simplified Chinese
Localization
-
SUNWhsmh – Service Availability Manager online
help package for Sun Management Center server layer for Traditional Chinese
Localization
Installing Service Availability Manager
You can install the Service Availability Manager add-on software either using the installation
wizard or the command line. This section discusses how to use the installation
wizard. For information about installing using the command line, see Appendix B, Installing Using the Command Line.
The Service Availability Manager software can be installed at the same time that you
install the Sun Management Center 3.5 software. You can also perform installation after Sun Management Center 3.5
is already installed. Installation of Service Availability Manager follows the standard Sun Management Center 3.5
add-on software installation procedures.
Service Availability Manager must be installed on the following layers of Sun Management Center 3.5:
Installation on the console layer is optional.
To Install Service Availability Manager During Sun Management Center 3.5 Installation
-
For more information and detailed steps, see Sun Management Center 3.5 Installation and Configuration
Guide.
To Install Service Availability Manager Individually
Note –
Perform this procedure only after the Sun Management Center 3.5 software has
been installed.
-
As superuser (su -), launch the Sun Management Center 3.5 installation
wizard by typing:
# /opt/SUNWsymon/sbin/es-guiinst
|
where /opt is the directory in which Sun Management Center 3.5
is installed. Substitute the name of the actual directory if it is different
on your system.
The Sun Management Center 3.5 installation wizard appears.
-
Provide the source directory of the Service Availability Manager files when prompted.
-
If installing from the software CD-ROM and the path is not
provided, type:
/cdrom/sunmanagementcenter_3_5/image
|
-
If installing from a directory to which the software has been
copied, type:
where disk1 is the corresponding name of
the location where the software was copied. You can also use the Browse button
to locate the directory.
-
If installing on the server layer, select the languages from the Select
Language Support panel and click Next.
The Checking for Available Products panel appears. When the progress
bar is finished, the Products Already Installed panel appears.
-
Review the list of products already installed and click Next.
The Select Add-on Products panel appears.
-
Select Service Availability Manager from the list of add-on software to be installed
and click Next.
The Add-on Products License Agreement panel appears.
-
Read the license agreement. You must click the I Agree button to proceed
with installation and then click Next.
The Confirmation Panel appears.
-
Review the Confirmation Panel and click Next.
The Installation Complete panel is displayed when the software installation
is complete.
Once installation of the Service Availability Manager software is complete, the setup
wizard guides you through the setup process for the software. For more information,
see Setting Up Service Availability Manager.
Setting Up Service Availability Manager
After installation is complete, you must run the Service Availability Manager setup wizard to configure the server and
agent layers. You can perform the setup procedure directly after the software
installation is complete. You can also exit the installation wizard and perform
the setup procedure later. The Sun Management Center 3.5 core server layer must be set
up before starting the Service Availability Manager setup procedure.
The Sun Management Center 3.5 installation wizard can launch the Service Availability Manager
setup wizard. The setup wizard appears after the Installation Complete panel
when using the installation wizard. The Service Availability Manager setup wizard guides
you through the setup procedure. For the command-line instructions for running
the setup script, see Appendix B, Installing Using the Command Line.
To Set Up Service Availability Manager During Sun Management Center 3.5 Installation
-
For more information and detailed steps, see Sun Management Center 3.5 Installation and Configuration
Guide.
To Set Up Service Availability Manager Individually
Note –
Perform this procedure only after the Sun Management Center 3.5 software has
been already installed. This procedure assumes that you chose not to set up Service Availability Manager
at the end of the Sun Management Center 3.5 installation process.
-
As superuser (su -), launch the Sun Management Center 3.5 setup
wizard by typing:
# /opt/SUNWsymon/sbin/es-guisetup
|
where /opt is the directory in which Sun Management Center 3.5
is installed. Substitute the name of the actual directory if it is different
on your system.
The Sun Management Center 3.5 setup wizard appears and guides you through the setup
process for the software.
Note –
If you have installed more than one add-on product, the setup
wizard for each product appears automatically. Each wizard guides you through
the setup process for its add-on product. Each new setup wizard appears automatically
after the setup process is completed for the previous add-on product. The
setup wizard for the Service Availability Manager software may not be the first to appear,
in this case.
-
The Overview panel appears first. Click Next to continue through the
wizard panels.
-
Review the list in the Stopping Components panel and click Next.
The Sun Management Center components must be stopped before the setup
process can continue.
-
The Advanced Setup Options panel appears if you have completed the setup
process for some of the add-on products installed. The remaining add-on software
can be set up now. Select from the following options and click Next:
-
Reconfigure All – The setup process is run again for
the base Sun Management Center 3.5 software and all add-on software. All of the Sun Management
Center software that was previously set up is set up again.
-
Configure Addons – The add-on software that was recently
installed but not yet set up is now set up.
-
Review the list of products in the Sun Management Center Base Product
Setup Complete panel and click Next.
The Select Add-on Products panel appears. All products newly installed
on the system that will be set up are listed. You are also given the option
to run setup again on any product that has already been set up.
-
Confirm that Service Availability Manager appears as a product to be set up now and
click Next.
The setup progress bar appears. Once the progress bar is done, the Add-on
Products Setup panel appears.
Once the setup procedure is complete, you have the option to start the
Sun Management Center processes. For more information, see Sun Management Center 3.5 Installation and Configuration
Guide.
Agent Update Feature
The Service Availability Manager 3.5
server layer must be installed before using the Sun Management Center 3.5 Agent Update
feature to upgrade the agent layer. The update image wizard prompts you to
select from the list of products to include in the update image. You must
select Service Availability Manager for inclusion in the update image. For information about
using the Agent Update feature, see Sun Management Center 3.5 Installation and Configuration Guide.
Upgrading to Service Availability Manager 3.5
If you have an installation of Service Availability Manager 3.0 on your
system, the earlier software must be uninstalled first. The Sun Management Center 3.5
installation wizard asks you whether you want to preserve your data files
before removing the software. The installation wizard then proceeds to install
the Service Availability Manager 3.5 software. For more information, see Sun Management Center 3.5 Installation and Configuration
Guide.
Uninstalling Service Availability Manager
Use the Sun Management Center 3.5 uninstall wizard to remove the Service Availability Manager software.
The uninstall wizard removes both the Service Availability Manager packages and data and
configuration changes made during setup. For more information about using
the uninstall wizard, see Sun Management Center 3.5 Installation and Configuration
Guide.
To Remove the Service Availability Manager Software
-
As superuser (su -), launch the uninstall wizard
by typing:
# /opt/SUNWsymon/sbin/es-guiuninst
|
where /opt is the directory in which Sun Management Center 3.5
is installed. Substitute the name of the actual directory if it is different
on your system.
The Sun Management Center 3.5 uninstall wizard appears.
-
Select Service Availability Manager from the list of software, and click Next.
-
Do not select to save the data files and click Next.
The Product Removal Screen appears.
-
Review the names of the products selected for removal and click Next.
The Service Availability Manager packages, configuration files, and data files are
removed. The Uninstall Summary panel appears when removal is completed.
-
Click Close to exit the wizard.
Dieses Buch im PDF-Format herunterladen (539 KB)