Default Solstice SyMON Rules

This appendix describes the default rules for this release of Solstice SyMON. Use this appendix to determine the rules that are incorporated into this Solstice SyMON release. By identifying the default rules, you can determine whether or not you need to write a new rule.

Note - The sample.tcl file in Solstice SyMON 1.1 through 1.3 contained only a comment.

TABLE D-1 describes the default rules supplied with this release of Solstice SyMON. The columns in the table describe the following:

Column 1 is the rule number.
Column 2 is a description of the rule.
Column 3 is the action taken when the condition is true.

TABLE D-1

Rule Number..Description	Action
General: `syrules.tcl`
0....`Symond` status	`alarm, snmp`
1....Server status	`alarm, snmp`
3....Log Scanner status	`alarm, snmp`
4....Kernel Reader status	`alarm, snmp`
6....Delay initial Log Scanner `and` death status	none
7....Delay initial Kernel Reader death status 8....Warning if label contains `"."`	none
9....Warning if label contains `"*"`	`alarm, snmp`
General: `egrules.tcl`

TABLE D-1 (Continued)

Rule Number..Description	Action
50....Trim event log if getting full	`alarm, snmp`
52....Warning when `ls_hist` is corrupted	`alarm, snmp`
53....Warning on incorrect Tcl rule syntax	`alarm, snmp`
General: `swrules.tcl`
100...Disk busy	`alarm, snmp`
102...Swap space	`alarm, snmp`
103...CPU swapping and paging	`alarm, snmp`
104...CPU load	`alarm, snmp`
105...File system full	`alarm, snmp`
106...No swap space	`alarm, snmp`
General: `hwrules.tcl`
209...SIMM error	`alarm, snmp`
210...`ssd` hardware error	`alarm, snmp`
211...`ssd` fatal error	`alarm, snmp`
212...SIMM error	`alarm, snmp`
214...`configd.*.status` failing	`alarm, snmp`
216...CPU panic	`alarm, snmp`
217...Tape error rate high	`alarm, snmp`
219...`ssd` off-line	`alarm, snmp`
220...`ssd` okay (online)	`alarm, snmp`
222...Fatal SunVTS error	`alarm, snmp`
223...SunVTS error	`alarm, snmp`
General: `pfrules.tcl`
300...SIMM errors	`add_pfa SIMM`
301...Disk soft errors	`add_pfa DISK`
302...Disk soft errors from smart drives	`alarm, snmp`
303...Check SIMM (test period 1)	`alarm, snmp`
304...Check SIMM (test period 2)	`alarm, snmp`
305...Check SIMM (test period 3)	`alarm, snmp`
306...Check disk `pfa` (warning)	`alarm, snmp`

TABLE D-1 (Continued)

Rule Number..Description	Action
307...Check disk `pfa` (severe)	`alarm, snmp`
308...Trims `pfa` history	none
General: `cprules.tcl`
400...CPU overload over x hours	`alarm, snmp, add_cpa`
401...Disk busy over x hours	`alarm, snmp, add_cpa`
402...Swap space low over x hours	`alarm, snmp, add_cpa`
403...Meta CPU events (`check_cpa_cpu`)	`alarm, snmp`
404...Meta disk events (`check_cpa_disk`)	`alarm, snmp`
405...Meta swap events (`check_cpa_swap`) 406...Trims `cpa` history 407...Initializes timestamp for rules 400 and 402	`alarm, snmp`
Platform-Specific Rules: SPARCserver 1000(E), SPARCcenter 2000(E ) - `SS1000.tcl, SC2000.tcl`
1002...Config Reader status	`alarm, snmp`
1005...Delay initial Config Reader death status	none
1207...`system...*.status`	`alarm, snmp`
1208...`system.......status`	`alarm, snmp`
1224a..`system.......*.status`	`alarm, snmp`
1225...Corrected ECC error 1230a..Sun StorEdge A3000 (formerly RSM Array 2000) controller and disk status; matches `system.........status`	`alarm. snmp`
Platform-Specific Rules: Sun Enterprise 450: `UE450.tcl`
1002...Config Reader status	`alarm, snmp`
1005...Delay initial configd death status	none
1204...`system.*.fan.status`	`alarm, snmp`
1205...`system...*.temperature`	`alarm, snmp, mailto`
1207...`system...*.status`	`alarm, snmp`

TABLE D-1 (Continued)

Rule Number..Description	Action
1208...`system...st.status`	`alarm, snmp`
1212...`system.power-supply.state`	`alarm, snmp`
1213...`system.power-supply.limit`	`alarm, snmp`
1214...`system.power-supply.current-share`	`alarm, snmp`
1215...`system.power-supply.temperature`	`alarm, snmp, mailto`
1224...`system.......*.status`	`alarm, snmp`
1226...`system.system-board.*.mc.bank.status`	`alarm, snmp`
1227...`system.system-board.*.mc.bank.dimm.status`	`alarm, snmp`
Platform-Specific Rules: Sun Enterprise 250 `UE250.tcl`
1002...Config Reader status	`alarm, snmp`
1005...Delay initial configd death status	none
1204...`system.cpu-fans.status.status`	`alarm, snmp`
1205...`system.system-board.*.cpu-unit.temperature`	`alarm, snmp, mailto`
1207...`system...*.status`	`alarm, snmp`
1208...`system...st.status`	`alarm, snmp`
1212...`system.power-supply.state`	`alarm, snmp`
1224...`system.......*.status`	`alarm, snmp`
1226...`system.system-board.*.mc.bank.status`	`alarm, snmp`
1227...`system.system-board.*.mc.bank.dimm.status`	`alarm, snmp`
Platform-Specific Rules: Sun Enterprise 3x00 -6x00: `UEnterprise.tcl`
1002...Config Reader status	`alarm, snmp`
1005...Delay initial Config Reader death status	none
1201...Hot plug charge DC status	`alarm, snmp`
1202...Hot plug precharge DC status	`alarm, snmp`
1203...`system.*.status`	`alarm, snmp`
1204...Fan status	`alarm, snmp`

TABLE D-1 Default Solstice SyMON Rules (Continued)


 Rule  
 Number      Description                             Action  


 1205        CPU board temperature                   alarm, snmp,  
                                                     mailto  
 1206        I/O and clock board temperature         alarm, snmp,  
                                                     mailto  
 1207        system.*.*.*.status                     alarm, snmp  
 1208        system.*.*.*.*.*.status                 alarm, snmp  
 1209        system.*.*.*.*.*.*.status               alarm, snmp  
 1213        Hot plug "removed"                      alarm, snmp  
 1215        Hot plug "hotplugged into"              alarm, snmp  
 1218        system.*.*.*.*.status                   alarm, snmp  
 1219        AC status  
 1220        Hot plug "installed"                    alarm, snmp  
 1221        Redundant power status                  alarm, snmp  
 1230        Sun StorEdge A3000 (formerly RSM Array  
             2000) controller and disk status; matches  
             system.*.*.*.*.*.*.*.status  

 
Platform-Specific Rules:  Sun Enterprise 150: UEnterpriseI.tcl  
 1002        Config Reader status                     alarm, snmp  
 1005        Delay initial configd death status      none  
 1207        system.*.*.*.status                     alarm, snmp  
 1208        system.*.*.*.*.*.*.status               alarm, snmp  

 
Storage-Specific Rules: Sun StorEdge A5000 (formerly Sun Enterprise Network  
 Array): SENA.tcl  
 5010        Backplanes; SES data to test for        alarm, snmp  
             status=critical  
 5011        Interconnect failure; SES data to test foralarm, snmp  
             EPROM failure  
 5012        Disk slots; SES data to test for over   alarm, snmp  
             temperature warning or failure for front disks  
 5013        Disk slots; SES data to test for under  alarm, snmp  
             temperature warning or failure for rear disks

TABLE D-1 (Continued)

Rule Number..Description	Action
5020...Disk slots; SES data to test for fault or fault requested (front disks)	`alarm, snmp`
5021...Disk slots; SES data to test for fault or fault requested (rear disks)	`alarm, snmp`
5030...Gigabit Interface Converter (GBIC)*; SES data to test for transmit failure	`alarm, snmp`
5035...Interface boards; SES data to test for over temperature	`alarm, snmp`
5037...Interface boards; SES data to test for loop 0 fault	`alarm, snmp`
5038...Interface boards; SES data to test for loop 1 fault	`alarm, snmp`
5040...Power supplies; SES data to test for over temperature warning or failure	`alarm, snmp`
5045...Power supplies; SES data to test for DC under or over voltage	`alarm, snmp`
5047...Power supplies; SES data to test for DC over current	`alarm, snmp`
5049...Power supplies; SES data to test for AC failure	`alarm, snmp`
5060...Fan trays; SES data to test for fan failure	`alarm, snmp`
* GBIC (see Rule 5030) is a plug in module that converts signals from a fibre optic cable to work with the host adapter card.