Disk LEDs Test 

Determines the number of disks that are present and the state of each disk. Illuminates each LED on the disk backplane to amber, and then back to its original state. The test then illuminates all disk LEDs to amber, and then back to their original state. This test is only enabled in Functional test. 

Fan Test 

Sets the fanbank speed to halfway between the current speed and max speed, then verifies the correct speed. Next, the fanbank speed is set to max speed, and the speed is verified. The fanbank speeds are then returned to normal, and then verified. This test is only enabled in Functional test. 

Front Panel and Keyswitch Test 

Flashes each individual LED on the front panel to ON (green or amber), then OFF, and then back to its original state. The test then illuminates all front panel LEDs then sets them back to their original state. The power on LED is read-only and will not be cycled. The test then displays the current keyswitch position. This test is only enabled in Functional test. 

Power Supply Status 

Identifies the number of power supplies that are in the system and the state of each power supply. This test is enabled in all modes. 

Temperature Status 

Identifies the current temperature of each CPU in the system, the ambient temperatures of the system, the temperature on the SCSI and power distribution boards, and verifies that all temperatures are within normal operating parameters. This test is enabled in all modes. 

Connection Test 

Reports the status of the power supplies, the temperature sensors within the system, and verifies normal operating parameters 

Functional Test 

Tests the disk back panel, front panel LEDs, and fan control circuitry. Also uses the same functionality as Online mode and connection test 

If you invoke SunVTS through SyMON, the following Functional Test description applies: Uses the same functionality as connection test (above) 

dev=raw_device_name

Specifies the name of the raw device to test 

diskleds=enable|disable

Enables or disables diskleds test 

env_mon=poll_interval 

Displays all system environmental statics every "poll_interval" seconds. (Display ONLY, Does not test.) 

fans=enable|disable

Enables or disables fans test 

fpanel=enable|disable

Enables or disables front panel test 

psupply=enable|disable

Enables or disables power supply test 

temp=enable|disable

Enables or disables temperature test 

8000

Unable to open driver driver name: sys error msg

Device name is wrong or driver is not loaded. 

Check the device name (if entered) or load driver. 

Device busy. 

Kill all other processes accessing driver. 

8001

kstat_open failed

No kernel resource available. 

Consult /var/adm/messages file for more information.

System software error 

8002

kstat_lookup failed for env2test structure in kstat module

env2test module not found.

Check revision and reload envctrl driver.

No kernel resource available 

Consult /var/adm/messages file for more information.

System software error. 

8003

kstat_read failed env2test structure in kstat module

env2test module not found.

Check revision /reload envctrl driver.

No kernel resource available. 

Consult the /var/adm/messages file for more information.

System software error. 

8004

Unable to close kstat

No kernel resource available. 

Consult the /var/adm/messages file for more information.

System software error. 

8005

Unable to set mode to DIAG using ioctl.: sys error msg

System software error 

Consult the /var/adm/messages file for more information.

8006

Unable to set disk LEDs: sys error msg

System software error 

Consult the /var/adm/messages file for more information.

8007

Unable to get disk LEDs: sys error msg

System software error. 

Consult the /var/adm/messages file for more information.

8008

Unable to set fan speed to speed: sys error msg

Fan hardware failure 

Manually check the fan speed and replace the fan. 

System software error. 

Consult the /var/adm/messages file for more information.

8009

Unable to get fan speed: sys error msg

System software error 

Consult the /var/adm/messages file for more information.

8010

Fan speed speed out of range: MIN speed MAX speed

Fan hardware failure. 

Manually check the fan speed and replace the fan. 

System software error. 

Consult the /var/adm/messages file for more information.

8011

Forced fan fault did not occur for fan type fanbank

Hardware failure. 

Replace the hardware. 

System software error. 

Consult the /var/adm/messages file for more information.

8015

Power Supply supply has failed: State

state

Power supply hardware failure. 

Replace the power supply. 

8016

Unable to allocate memory using malloc. : sys error msg

System software error. 

Consult the /var/adm/messages file for more information.

8017

Unable to set mode to NORMAL using ioctl. : sys error msg

System software error. 

Consult the /var/adm/messages file for more information.

8018

Error encountered during call to function name

8019

Unable to set front panel LEDs using ioctl.: sys error msg

System software error. 

Consult the /var/adm/messages file for more information.

8020

Unable to reset front panel LEDs to original state

System software error. 

Consult the /var/adm/messages file for more information.

8021

Unable to get front panel LEDs.

System software error. 

Consult the /var/adm/messages file for more information.

8022

Ambient temperature temperature Celsius out of range

envctrl hardware error.

8023

CPU CPU # temperature temperature Celsius out of range

envctrl hardware error.

8024

Data Miscompare: ioctl diskled mask = diskled mask kstat diskled mask = diskled mask

hardware error 

System software error. 

Consult the /var/adm/messages file for more information.

8025

Illegal options passed to env2test option

User error. 

Check usage by typing env2test -u.

8026 

Unable to retrieve power supply information. 

I2C hardware failure. 

Replace power supply. 

I2C bus wedged. 

Check for other I2C devices that may be corrupting the I2C bus. 

8033 

Temperature temperature celsius out of range.

Hardware error. 

Check all thermistors.