Disk LEDs Test

Illuminates each LED on the disk backplane(s) to green, then amber, and then back to its original state. The test then illuminates all disk LEDs to green, then amber, and then back to their original state. This test is only enabled in Functional test mode.

Fan Test

Cycles each fanbank speed to low, medium, and high, then verifies the correct speed. Next, each fanbank is stopped, one at a time. The test then verifies that a fan fault has occurred. Next, the watchdog timer is invoked to simulate a catastrophic failure. The test verifies that the system set all fanbanks to high and then resets the fan speed to normal. This test is only enabled in Functional test.

Front Panel and Keyswitch Test

Flashes each individual LED on the front panel to ON (green or amber), then OFF, and then back to its original state. The test then illuminates all front panel LEDs then sets them back to their original state. The power on LED is Read Only and will not be cycled. The test then displays the current keyswitch position. This test is only enabled in Functional test mode.

Power Supply Status

Identifies the number of power supplies that are in the system, and the state of each power supply, and verifies that the power supply temperatures are within normal operating parameters. This test is enabled in all modes.

Temperature Status

Identifies the current temperature of each CPU in the system, and the ambient temperature of the system, and envtest verifies that all temperatures are within normal operating parameters. This test is enabled in all modes.

Connection Test

Reports the status of the power supplies, the temperature sensors within the system, and verifies normal operating parameters.

Functional Test

Tests the disk back panel, front panel LEDs, and fan control circuitry. Also uses the same functionality as Online mode and connection test

If you invoke SunVTS through SyMON, the following Functional Test description applies:

envtest runs in Connection Test mode (see description above).

dev=raw_device_name

Specifies the name of the raw device to test.

diskleds=enable|disable

Enables or disables the diskleds test.

fans=enable|disable

Enables or disables the fans test.

fpanel=enable|disable

Enables or disables the front panel test.

psupply=enable|disable

Enables or disables the power supply test

temp=enable|disable

Enables or disables the temperature test.

8000

Unable to open driver driver_name: sys error msg

Device name is wrong or driver is not loaded.

Check the device name (if entered) or load driver.

Device busy.

Kill all other processes accessing driver.

8001

kstat_open failed

No kernel resource available.

Consult /var/adm/messages file for more information.

System software error

8002

kstat_lookup failed for envtest structure in kstat module

envtest module not found.

Check revision and reload envctrl driver.

No kernel resource available.

Consult /var/adm/messages file for more information.

System software error.

8003

kstat_read failed envtest structure in kstat module

envtest module not found.

Check revision /reload envctrl driver.

No kernel resource available.

Consult the /var/adm/messages file for more information.

System software error.

8004

Unable to close kstat

No kernel resource available.

Consult the /var/adm/messages file for more information.

System software error

8005

Unable to set mode to DIAG using ioctl.: sys error msg

System software error

Consult the /var/adm/messages file for more information.

8006

Unable to set disk LEDs: sys error msg

System software error

Consult the /var/adm/messages file for more information.

8007

Unable to get disk LEDs: sys error msg

System software error.

Consult the /var/adm/messages file for more information.

8008

Unable to set fan type fan speed to speed: sys error msg

Fan hardware failure.

Manually check the fan speed and replace the fan.

System software error.

Consult the /var/adm/messages file for more information.

8009

Unable to get fan type fan speed: sys error msg

System software error.

Consult the /var/adm/messages file for more information.

8010

fan type fan speed: speed out of range

Fan hardware failure.

Manually check the fan speed and replace the fan.

System software error.

Consult the /var/adm/messages file for more information.

8011

Forced fan fault did not occur for fan type fanbank

Hardware failure.

Replace the hardware.

System software error.

Consult the /var/adm/messages file for more information.

8012

Forced fan fault did not clear for fan type fanbank

Hardware failure.

Replace the hardware.

System over temperature.

Consult the /var/adm/messages file for more information.

System software error.

8013

Unable to set watchdog timer

Hardware failure.

Replace the hardware.

System software error.

Consult the /var/adm/messages file for more information.

8014

Unable to set temperature to temperature

System software error.

Consult the /var/adm/messages file for more information.

8015

Power Supply supply has failed: Limit 0=PASS|1=FAIL Current Share 0=PASS|1=FAIL Temperature temperature

Power supply hardware failure.

Replace the power supply.

8016

Unable to allocate memory using malloc. : sys error msg

System software error.

Consult the /var/adm/messages file for more information.

8017

Unable to set mode to NORMAL using ioctl. : sys error msg

System software error.

Consult the /var/adm/messages file for more information.

8018

Error encountered during call to function name

8019

Unable to set front panel LEDs using ioctl.: sys error msg

System software error.

Consult the /var/adm/messages file for more information.

8020

Unable to reset front panel LEDs to original state

System software error.

Consult the /var/adm/messages file for more information.

8021

Unable to set front panel LEDs to led mask

System software error

Consult the /var/adm/messages file for more information.

8022

Ambient temperature: temperature Celsius out of range

envctrl hardware error.

8023

CPU CPU # temperature: temperature Celsius out of range

envctrl hardware error.

8024

Data Miscompare: ioctl diskled mask = diskled mask kstat diskled mask = diskled mask

envctrl hardware error

System software error.

Consult the /var/adm/messages file for more information.

8025

Illegal options passed to envtest option

User error.

Check usage by typing envtest -u.

8026

Unable to retrieve power supply information.

I2C hardware failure

Replace power supply.

I2C bus wedged

Check for other I2C devices that may be corrupting the I2C bus.

8027

Power Supply Over Temperature: PS Slot slot PS Temperature temperature.

Bad Power Supply.

Replace Power Supply.