Default Solstice SyMON 1.3 Rules

D

This appendix describes the default Solstice SyMON 1.3 rules. Use this appendix to determine the rules that are incorporated into Solstice SyMON 1.3. By identifying the default rules, you can determine whether or not you need to write a new rule.

Table D-1 describes the default rules supplied with Solstice SyMON 1.3. The columns in the table describe the following:

Column 1 is the rule number.
Column 2 is a description of the rule.
Column 3 is the action taken when the condition is true.
Column 4 is the severity.
Column 5 is the priority.

Table D-1

Rule Number	Description	Action
General: `syrules.tcl`
0	`Symond` status	`alarm, snmp`
1	Server status	`alarm, snmp`
3	Log Scanner status	`alarm, snmp`
4	Kernel Reader status	`alarm, snmp`
6	Delay initial Log Scanner and death status	none

Table D-1 (Continued)

Rule..Description Number	Action
7....Delay initial Kernel Reader death status 8....Warning if label contains `"."`	none
9....Warning if label contains `"*"`	`alarm, snmp`
General: `egrules.tcl`
50...Trim event log if getting full	`alarm, snmp`
51...Warning when maximum number of events is near	`alarm, snmp`
52...Warning when `ls_hist` is corrupted	`alarm, snmp`
53...Warning on incorrect Tcl rule syntax	`alarm, snmp`
General: `swrules.tcl`
100...Disk busy	`alarm, snmp`
102...Swap space	`alarm, snmp`
103...CPU swapping and paging	`alarm, snmp`
104...CPU load	`alarm, snmp`
105...File system full	`alarm, snmp`
106...No swap space	`alarm, snmp`
General: `hwrules.tcl`
209...SIMM error	`alarm, snmp`
210...`ssd` hardware error	`alarm, snmp`
211...`ssd` fatal error	`alarm, snmp`
212...SIMM error	`alarm, snmp`
214...`configd.*.status` failing	`alarm, snmp`
216...CPU panic	`alarm, snmp`
217...Tape error rate high	`alarm, snmp`
219...`ssd` off-line	`alarm, snmp`
220...`ssd` okay (online)	`alarm, snmp`
222...Fatal SunVTS error	`alarm, snmp`

Table D-1 (Continued)

Rule..Description Number	Action
223...SunVTS error General: `pfrules.tcl`	`alarm, snmp`
300...SIMM errors	`add_pfa SIMM`
301...Disk soft errors	`add_pfa DISK`
302...Disk soft errors from smart drives	`alarm, snmp`
303...Check SIMM (test period 1)	`alarm, snmp`
304...Check SIMM (test period 2)	`alarm, snmp`
305...Check SIMM (test period 3)	`alarm, snmp`
306...Check disk `pfa` (warning)	`alarm, snmp`
307...Check disk `pfa` (severe)	`alarm, snmp`
308...Trims `pfa` history	none
General: `cprules.tcl`
400...CPU overload over x hours	`alarm, snmp, add_cpa`
401...Disk busy over x hours	`alarm, snmp, add_cpa`
402...Swap space low over x hours	`alarm, snmp, add_cpa`
403...Meta CPU events (`check_cpa_cpu`)	`alarm, snmp`
404...Meta disk events (`check_cpa_disk`)	`alarm, snmp`
405...Meta swap events (`check_cpa_swap`) 406...Trims `cpa` history 407...Initializes timestamp for rules 400 and 402	`alarm, snmp`
Platform-Specific Rules: SPARCserver 1000(E), SPARCcenter 2000(E ):- `SS1000.tcl, SC2000.tcl`
1002..Config Reader status	`alarm, snmp`
1005..Delay initial Config Reader death status	none
1207..`system...*.status`	`alarm, snmp`

Table D-1 Default Solstice SyMON 1.3 Rules (Continued)


 Rule        Description                             Action  
 Number  


 1208        system.*.*.*.*.*.*.status               alarm, snmp  
 1224        system.*.*.*.*.*.*.*.status             alarm, snmp  
 1225        Corrected ECC error                     alarm, snmp  

 
Platform-Specific Rules:  Ultra Enterprise 3000, 4000, 5000, 6000:  
 UEnterprise.tcl  
 1002        Config Reader status                     alarm, snmp  
 1005        Delay initial configd death status      none  
 1201        Hot plug charge DC status               alarm, snmp  
 1202        Hot plug precharge DC status            alarm, snmp  
 1203        system.*.status                         alarm, snmp  
 1204        Fan status                              alarm, snmp  
 1205        CPU board temperature                   alarm, snmp,  
                                                     mailto  
 1206        I/O and clock board temperature         alarm, snmp,  
                                                     mailto  
 1207        system.*.*.*.status                     alarm, snmp  
 1208        system.*.*.*.*.*.status                 alarm, snmp  
 1209        system.*.*.*.*.*.*.status               alarm, snmp  
 1213        Hot plug "removed"                      alarm, snmp  
 1215        Hot plug "hotplugged into"              alarm, snmp  
 1218        system.*.*.*.*.status                   alarm, snmp  
 1220        Hot plug "installed"                    alarm, snmp  
 1221        Redundant power status                  alarm, snmp  

 
Platform-Specific Rules:  Ultra Enterprise 2 and 150: UEnterpriseI.tcl  
 1002        Config Reader status                     alarm, snmp  
 1005        Delay initial configd death status      none

Table D-1 (Continued)

Rule Number	Description	Action
1207	`system...*.status`	`alarm, snmp`
1208	`system.......status`	`alarm, snmp`
1224	`system.........*.status`	`alarm, snmp`