Inom
Hitta mer dokumentation
Supportresurser som ingår
|  Ladda ner denna bok i PDF
Index
Symbols
| |
| /etc/vold.conf |
| .....default | 54 |
| .....updating | 54 |
A
| |
| aborting |
| .....Break | 81 |
| .....L1-a | 81 |
| .....Stop-a | 81 |
| address |
| .....device | 68 |
| .....selecting | 67 |
| ............board | 62 |
| ............CD-ROM drive | 32, 47, 49 |
| ............disk drive | 67 |
B
| |
| backup commands | 36 |
| board |
| .....address selection | 62 |
| booting |
| .....abort | 81 |
| .....how to abort |
| ............SPARC | 81 |
| .....to multiuser state |
| ............SPARC | 79 |
| .....to single-user state |
| ............SPARC | 79 |
| booting to multiuser state |
| .....SPARC | 79 |
| booting to single-user state |
| .....SPARC | 79 |
| Break key | 81 |
C
| |
| CD-ROM drive |
| .....adding a secondary | 55 |
| .....configuring | 55 |
| .....mount points | 57 |
| command |
| .....backup | 36 |
| .....cpio | 37 |
| .....dd | 38 |
| .....tar | 42 |
| .....ufsdump | 38 |
| .....ufsrestore | 40 |
| configuring the system |
| .....board | 62 |
| .....CD-ROM drive | 55 |
| .....tape drive | 31 |
| cpio command | 31, 37 |
D
| |
| dd command | 31, 38 |
| default |
| .....modules directory path |
| ............x86 | 80 |
| .....root file system type |
| ............x86 | 80 |
| .....system file (/etc/system) |
| ............x86 | 80 |
| device address |
| .....board | 62 |
| .....example | 68 |
| .....tape drive | 33 |
| device driver | 9 |
F
| |
| file system |
| .....default root |
| ............x86 | 80 |
H
| |
| halting a system | 4 |
| .....withhalt | 4 |
| .....withinit | 4 |
| .....withreboot | 4 |
| .....withshutdown | 4 |
I
| |
| ID number |
| .....logical controller | 69 |
| .....logical disk | 72 |
| .....logical target | 70 |
| init state | 5 |
| .....uses of | 5 |
| Intelligent Peripheral Interface (IPI) | 66 |
| interactive |
| .....booting |
| ............SPARC | 80 |
| interface |
| .....Intelligent Peripheral Interface(IPI) | 66 |
| .....peripheral device | 66 |
| ......Small Computer System Interface(SCSI) | 66 |
L
| |
| L1-A command | 81 |
| logical |
| ......controller ID number | 69 |
| ......disk ID number | 72 |
| ......target ID number | 70 |
M
| |
| modules directory path, default |
| ......x86 | 80 |
| mounting a CD-ROM | 47, 48, 49 |
| multiuser state |
| ......booting to |
| ............SPARC | 79 |
P
| |
| peripheral bus | 66 |
| ......Sbus | 66 |
| ......VMEbus | 66 |
| peripheral device |
| ......type of interface | 66 |
| ......type of peripheral bus | 66 |
| probe-ipi command | 70 |
| probe-scsi command | 8, 12 |
| PROM |
| ......prompt | 77 |
| prompt |
| ......PROM | 77 |
R
| |
| rebooting a system | 4 |
| restore command | 31 |
S
| |
| SBus | 66 |
| SCSI target IDs | 8, 12 |
| shutting down a system | 4 |
| |
| .....withhalt | 4 |
| .....withinit | 4 |
| .....withshutdown | 4 |
| .....withreboot | 4 |
| shutting down the system | 3 |
| single-user |
| .....booting to |
| ............SPARC | 79 |
| .....continue to multiuser state |
| ............SPARC | 79 |
| Small Computer System Interface(SCSI) | 66 |
| Stop-A command | 81 |
| system file |
| .....x86 | 80 |
T
| |
| tape drive |
| .....displaying status | 35 |
| tar command | 31, 42 |
| tensioning a tape cartride | 34 |
| touch /reconfigure command | 7, 10 |
U
| |
| ufsdump command | 31, 38 |
| ufsrestore command | 40 |
| uname -rs command | 2 |
V
| |
| verifying the operating environment | 2 |
| VME bus | 66 |
| vol |
| .....file system | 58 |
| volcheck |
| .....using to check for floppy in drive | 57 |
| Volume Management |
| .....adding new devices | 54 |
| .....configuring | 54 |
|
|
