Index

Numerics


10Base5 connector	B-3


height adjust, levelling pads	8-9


key switch
.....cabinet	7-2
.....location	7-6
kick panelSee panel, remove, kick


leveling pads, adjust	8-9


n	7-19, 7-20
network


.....primary	B-3


rear screen panelSee panel, remove
remove
.....panel
............hinged front, open	8-5
............kick	8-8
............rear screen	8-6
............side	8-7
............vented front	8-3, 8-5
removing and replacing
......rear panel	8-2
replace
......panel
............rear screen	8-7
............side	8-8
............vented front	8-4, 8-6
reset
......switch, initiate POST	7-16, 7-19
restart
......POST	7-16, 7-19
RJ45 connector pinout	B-2


............replacing system board andcomponents	9-2
............startup	7-6
.....SPARCstorage array	7-8
............complete array shutdown	7-8
............complete tray startup	7-9
............replacing majorsubassemblies	9-3
............replacing trays and drives	9-2
............single drive/ tray startup	7-11
............single drive/tray shutdown,7-11
.....system cabinet	7-2
............shutdown	7-2
............startup	7-4
.....terminal concentrator	7-11
............replacement of	9-5
SPARCcluster 2000HA	7-11
.....boot disks
............power off	7-20
............power on	7-20
............replacement of	9-9
.....cabling
............replacing	9-12
.....configurations	1-6
.....processor
............replacing system board andcomponents	9-8
.....processor shutdown/startup	7-17
.....SPARCstorage array
............complete array shutdown	7-19
............complete array startup	7-19
............replacing majorsubassemblies	9-9
............replacing trays and disks	9-8
............single disk/tray shutdown	7-19
............single disk/tray startup	7-20
.....system cabinet	7-11
............shutdown	7-12
............startup	7-13
.....terminal concentrator	7-20
............replacement of	9-11
specifications
.....environmental	A-1
.....temperature	A-1, A-6
stabilizer bar
......adjust	8-9
......safety	8-9
`stats` command	3-25
swapping cables, algorithm	3-27
switch
......key
............cabinet	7-4
......reset, initiate POST	7-16, 7-19


target
......address
............SPARCcluster 2000HA bootdisks	C-1
temperature specifications	A-1, A-6
terminal concentrator
......Ethernet, pinout	B-3
......indicator LEDs	3-27
......serial pinout	B-1
testing
......drive
............SBus card	7-16, 7-19
`tip hardwire` command	3-25, 3-26
tools required	6-5
tray
......use stabilizer bar	8-9
troubleshoolting
......hardware
............SPARCstorage Array
...................disk data path	3-4
troubleshooting
......error messages
............SPARCstorage Array	D-1
...................device driver	D-1
...................firmware	D-1
......error messages, list of	2-5
......fault classes	2-4
......flow	2-2
......hardware	3-1
............network
...................client net	3-20


...................private	3-17
............network failures	3-17
............node failures
...................boot disks	3-12
...................control board	3-12
...................system board	3-12
............serial connections	3-20
............SPARCstorage Array	3-5
...................controller board	3-3
............SPARCstorage Array/Opticalconnections	3-2
............terminal concentrator	3-20
...................flow diagrams	3-23
.....maintenance authorization	2-1
.....overview	2-1
.....principal assemblies	2-4
.....remote site	2-1
.....software	4-1
............operating system	4-2
............Oracle	4-2
............SPARCstorage Array	4-2
.....symptons, list of	2-5


vented front panel	8-3, 8-5